B&L Cremation BLI 2500 MW Incinerator

Our largest batch load system, the B&L Cremation Systems, Inc. BLI 2500 MW medical/pathological waste incinerator, has a primary chamber volume of 170 cubic feet and a burn rating of 250 pounds per hour.

Further information on fuel, oil, and specifications will be given upon request.

FULLY AUTOMATIC CONTROL SEQUENCE Operation is made simple by the fully automatic control sequence.  A microprocessor temperature controller, with a digital readout, ensures optimum control while providing the lowest fuel consumption.  Visual verification of each stage is provided on the control panel.  Operator override is achieved by a turn of a switch for semi-manual control.

MULTI-CHAMBER AIR CONTROLLED DESIGN The entire combustion process is completed within the air controlled chambers, eliminating burning in the stack, allowing for 24 hour operation, and providing for greater fuel efficiency over excess air designs.

POLLUTION MONITORING & CONTROL SYSTEM This system constantly monitors the stack gases to prevent visible emissions. Integrated with the automatic system, this feature enables the unit to make all necessary adjustments automatically.

REFRACTORY LINED STACK A three inch insulating liner is provided as a safety feature.  While gases seldom exceed 1,000°F, the liner reduces heat penetration under every condition, preventing the possibility of fire.  A ten year warranty is offered on the stack liner.

LOW NOISE The secondary combustion blower has been manufactured and installed to allow for low noise operation.

Length: 148″ (156″ with cremation burner)
Width: 72″ (84″ with control panel)
Height: 73″ (97″ with doorcap)
Weight: 38,000 lb
Gas
Pressure:
Natural Gas: 7″ W.C.
Propane Gas: 11″ W.C.
Power
Requirements:
With Auto Loader:
220 V, single phase, 64.50 AMPS
Without Auto Loader:
220 V, single phase, 48.50 AMPS
Incineration
Rate:
250 lb/hr
Body Weight
Capability:
2,500 lb
Stack Height
From Grade:
minimum 15′
Stack
Sections:
30″ O.D.
Refractory/
Insulation:
6″ firebrick walls
castable refractory lining
(hearth and ceiling)
3″ 1900 – board insulation
Chamber
Dimensions:
Length: 95″
Width: 56″
Height: 55″
169 ft³
Burner
Output:
Maximum Input Rating: 750,000 BTU’s per hour
Afterburner Maximum: 400,000 BTU’s per hour
Modulation Minimum: 100,000 BTU’s per hour
Cremation Burner: 350,000 BTU’s per hour
Air
Requirements:
Outside air inlet louvers in the room located at or below burner height, capable of passing 2,500 ft³ per minute of free air.
Length: 3.76 m (3.96 m with cremation burner)
Width: 1.83 m (2.13 m with control panel)
Height: 1.85 m (2.46 m with doorcap)
Weight: 17,236.51 Kg
Gas
Pressure:
Natural Gas: 1.74 kPa W.C.
Propane Gas: 2.74 kPa W.C.
Power
Requirements:
With Auto Loader:
220 V, single phase, 64.50 AMPS
Without Auto Loader:
220 V, single phase, 48.50 AMPS
Incineration
Rate:
113.40 Kg/hr
Body Weight
Capability:
1,133.98 Kg
Stack Height
From Grade:
4.57 m
Stack
Sections:
762 mm O.D.
Refractory/
Insulation:
0.15 m firebrick walls
castable refractory lining
(hearth and ceiling)
0.08 m 1900 – board insulation
Chamber
Dimensions:
Length: 2.41 m
Width: 1.42 m
Height: 1.39 m
4.79 m³
Burner
Output:
Maximum Input Rating: 791,291.70 KJ per hour
Afterburner Maximum: 422,022.24 KJ per hour
Modulation Minimum: 105,505.56 KJ per hour
Cremation Burner: 369,269.46 KJ per hour
Air
Requirements:
Outside air inlet louvers in the room located at or below burner height, capable of passing 1.18 m³ per second of free air.

N-20SA Human Crematory

The B&L Cremation Systems, Inc. N-20SA human crematory is our low volume production system, with average cremation times of 150 minutes.

N-20AA Human Crematory

The B&L Cremation Systems, Inc. N-20AA human crematory is our medium volume production system, with average cremation times of 100 to 120 minutes.

N-20 Human Crematory

The B&L Cremation Systems, Inc. N-20 human crematory is our low to medium volume production system, with average cremation times of 120 minutes.

Phoenix II-1 Human Crematory

The B&L Cremation Systems, Inc. Phoenix II-1 Human Crematory is our medium volume production system, with average cremation times of 70 to 90 minutes.  It has a 1,000 pound load capacity.

Phoenix II-2 Human Crematory

The B&L Cremation Systems, Inc. Phoenix II-2 human crematory is our medium to high volume production system, with average cremation times of 60 to 70 minutes.  It has a 1,000 pound load capacity.

Phoenix II-3 Human Crematory

The B&L Cremation Systems, Inc. Phoenix II-3 human crematory is our high volume, hot-load production system, with average cremation times of 45 to 60 minutes.  It has a 1,000 pound load capacity.

BLI 400 MW Incinerator

The B&L Cremation Systems, Inc. BLI 400 MW medical/pathological waste incinerator is our smallest system.  It has a primary chamber volume of 23 cubic feet, and an afterburner rating of 75 pounds per hour.

BLI 800 MW Incinerator

The B&L Cremation Systems, Inc. BLI 800 MW medical/pathological waste incinerator has a primary chamber volume of 54 cubic feet.  The burn rate is 100 pounds per hour.

BLI 1500 MW Incinerator

The B&L Cremation Systems, Inc. BLI 1500 MW medical/pathological waste incinerator is a batch load system.  It has a primary chamber volume of 110 cubic feet and is rated at 200 pounds per hour.

BLI 5000 MW Incinerator

The B&L Cremation Systems, Inc. BLI 5000 MW medical/pathological waste incinerator is a continuous feed style system with an operational rate of 350 pounds per hour.